Engineered to prevent damage to the sub-floor or wall cavity if moisture seeps through grouted tile, DensShield Tile Backer is the first backer board with a built-in moisture barrier. … Easier to handle than cement board, DensShield Tile Backer cuts and installs like drywall without special tools or fasteners.

DensShield Tile Backer is ideal for bathrooms, showers, floors, kitchens and other wet, high humidity areas.

White Lightning White Paintable All-Purpose Silicone Sealant – 9 oz. … Sign In.

DensShield is easier to work with (basically just drywall with a water proof membrane), whereas the Durock is basically a cement board so it’s a bit harder to work with. I would appreciate your advice. Thanks ! DensShield is easier to work with imo, and it is a smoother surface.

Yes. DensShield is manufactured to ASTM C 1178 and is listed as one of the three products acceptable as a backer board in wet areas.

the Competition. The moisture-resistant gypsum core resists the growth of mold. DensShield Tile Backer has the highest level of performance for mold resistance under the ASTM D3273 test method.

Dens-Shield may also be finished with paint or wallpaper for non-tile areas that require superior fire and moisture resistance where its vapor barrier and water- repelling qualities are desirable. Dens-Shield also adds stabilizing and fire-resistant qualities to countertop installations.

Standards and Code Compliance DensShield Tile Backer in 1/4 (6.4 mm), 1/2 (12.7 mm) and 5/8 (15.9 mm) thicknesses conforms to current IRC and IBC codes and is manufactured to meet ASTM C1178 as a fiberglass mat gypsum substrate for use as tile backer.

DensShield 1/2 in.x 4 ft.x 8 ft. Backer Board-855000 – The Home Depot.

Cement board Cement board is a good, reliable backer board that works well on both floors and walls. Keep in mind that most tile setters err on the side of caution and brush a waterproofing membrane on top of cement board when it is in wet areas like showers or tub surrounds.

DensShield Tile Backer is composed of a water-resistant treated core that is covered front and back with fiberglass mats. On the tile side, DensShield Tile Backer’s built-in coating on the surface stops surface water and retards moisture transmission, protecting the wall cavity.

Natural. Moisture Resistance. Triton Waterproof Backer Board is made with a revolutionary board comprised of naturally occurring magnesium oxide, a mineral innately resistant to moisture, mold, and mildew.

It is safe to install tile over drywall in areas of your home that do not experience excessive wetness as long as you prepare the wall before installation and use the right mortar. If you’re installing tile in your bathroom, it should be installed on a cement board or a tile backer meant for use in wet areas.

DensGlass is a gypsum panel with fiberglass mat facings and its widely recognized GOLD colored primer coating for superior mold and moisture resistance. For use as exterior substrate panel for walls, ceilings and soffits.

Be sure to figure the height of your tile backer board to be a minimum of 6 feet above the shower floor. This will keep you from having any moisture problems with your drywall. You may want to add in some waste for missed cuts.

DensGlass is not rated as a tile backer. I specifically asked the manufacturer about doing tile on it for an exterior and they said no way. DensArmor is a fiberglass faced gypsum product used as drywall that is rated as a tile backer.

DensGlass Sheathing adds performance and durability to a wide range of fire-rated and non-fire-rated building assemblies. Dens Solutions are industry trusted, high-performing fiberglass mat gypsum panels suitable for your wall, roof, ceiling and floor projects.

Placement of cement board undedr the tub is not necessary. In fact, place your tub on the subfloor but then install the cement backer right up to the tub. This limits lateral movement of the tub at the bottom of the skirt.

Charles Young, a technical service representative with Georgia-Pacific Gypsum in Atlanta, responds: In a typical residential shower, it is acceptable to skim-coat DensShield tile backer (Georgia-Pacific Gypsum, 800/225-6119, www.gp.com/build) with a setting-type joint compound such as Durabond (USG, 800/874-4968, www …

A: Yes, the steps to accomplish this are quite simple. First, finish the joints using fiberglass mesh tape and setting type joint compound. Next, skim the entire DensShield panel surface with setting compound.

Furthermore, thinset will not adhere to silicone. You’ve decided to use your own installation method.

With their designed-in strength and moisture resistance, Dens panels, when used on interior walls, deliver dimensional stability, moisture resistance and the highest level of performance for mould resistance under ASTM D3273 test method.

Providing superb protection from the elements, DensGlass Sheathing is resistant to delamination and deterioration due to weather exposure even during construction delays that last as long as twelve months after installation and are backed by a limited warranty against delamination and deterioration for up to 12 …

USG Securock Brand Glass-Mat Sheathing is a non-combustible, moisture- and mold resistant panel designed for use under exterior claddings where conventional gypsum sheathing products have traditionally been used, such as brick veneer, properly detailed Exterior Insulation Finish Systems (EIFS), Direct-applied Exterior …

Thinset mortar is waterproof in that; it can be used in wet areas such as a shower or outdoors.